Message Level

Error
Turns on message logging for errors only.
 
Warning
Turns on message logging for warnings and errors.
 
Info
Turns on message logging for all informational, warning and error messages.
 
Audit
Turns on message logging for all audit, informational, warning and error messages.
 
Trace
Allows all messages to be logged, including those used for debugging purposes.

Message Language

Specifies the language used to display error messages.

Universal Broker connection options

Use the following local interface for outbound connections
When this option is selected, the IP address or alias of a local interface may be specified that will be used whenever UEM Manager connects to a Universal Broker.
If this option is not selected, any available local interface will be used.
When more than one local interface is available, this option may be used to specify the IP address or host name that should be used whenever UEM Manager connects to a Universal Broker. To have UEM Manager use any local interface available, leave this value blank.
 
Use all IP addresses returned by DNS when resolving host names
When this option is selected, all IP addresses returned by a DNS query for a given host name are expanded in the list of hosts. When this option is not selected, only the first IP address for the resolved host name is used.
This option is not selected by default.
 
Default Host Name/IP Address
Enter one or more valid IP addresses and/or host names – separated by a comma – to use as the default system(s) for event monitoring. A specific port number may also be specified for any one of the hosts in the list. The format for this list of one or more hosts is: host1[port1,host2port2,...,hostnportn]
To monitor an event on the local system, enter a host name of localhost, or an IP address of 127.0.0.1.
 
Port Number
Enter a port number or service name that will be used to connect to Universal Broker.
 
Select the first host in a list using the following method
This option specifies how entries within a list of hosts are accessed as the Universal Event Monitor Manager attempts to establish a connection with a Universal Broker.
When the sequential selection method is chosen, connection attempts begin with the first host in the list. Connection attempts continue with each subsequent host in the list, until a connection to a Universal Broker is established or until all hosts in the list have been tried.
When the random method is chosen, connection attempts begin with a randomly selected host. Connection attempts continue with each host in the list until a connection is established or until the first host selected is reached again.
The default value for this option is sequential.
 
Retry host name resolution
Indicates the number of attempts that will be made to resolve a host name specified with the -host option on the Universal Event Monitor command line. This parameter can help resolve intermittent "host not found" errors.
 
Cancel Connect After
This option specifies how long the Universal Event Monitor Manager will wait for each connection attempt to a Universal Broker to complete before moving on to the next host in the list. If there are no more hosts in the list, or connection attempts to all the hosts time out, the Manager will terminate.
The default value for this option is 0 (zero), which instructs the UEM Manager to use the default TCP/IP timeout value. This results in a blocking connect attempt, and is provided to preserve compatibility with pre-v320 behavior.

Code Page

Sets the translation table used to translate text-based data transmitted across the network.

Network Delay

The network delay value specifies the maximum acceptable delay in the network. Should it take longer than the specified delay time to send or receive data over the network, the operation will end with a time out error. The default is 120 seconds.

Wait until the requested event becomes inactive before exiting

When this option is checked, the UEM Manager will, by default, wait for the event being monitored to become inactive before completing. This means that the Manager will not end until the demand-driven UEM Server that was started to monitor the event ends.
To cause the Manager to return as soon as the UEM Server begins monitoring the event, leave this option unchecked.

Make events inactive after detecting

This option is used to track the number of occurrences that are detected by a demand-driven UEM Server (that is, one started from a UEM Manager) for a given event. When the Server has detected the specified number of occurrences, the event will become inactive even if the inactive date/time has not elapsed. If the specified count is not reached by the inactive date/time, the event will become inactive at that time. A value of 0 (zero) will effectively disable this feature.

Internal Communication Ciphers List

Negotiate sessions using

(No help available.)